lps100-m series 150 watts total power: 80 - 150 watts input voltage: 90 - 264 vac 120 - 300 vdc # of outputs: single special features ? medical and ite safety approvals, 2x mopp ? active power factor correction ? 2 x 4 footprint ? less than 1u high ? en61000-3-2 compliant ? remote sense ? power fail ? adjustable main output ? built-in class b emi flter ? overvoltage protection ? overload protection ? thermal overload protection ? isolated 12 v fan output ? lpx100 enclosure kit available ? poe isolation on main output of lps109-m safety ? tuv 60950, 60601-1 ? ul 60950, 60601-1 ? culus 60950, 60601-1 ? cb certifcate & report ? ce mark (lvd) ? cqc mark electrical specifcations input input ra nge 90 - 264 vac; 120 - 300 vdc frequency 47 - 63 hz inrush current 50 a max., cold start @ 25 c effciency 88% typical at full load emi/rfi fcc class b conducted; cispr22 class b conducted; en55022 class b conducted; vde0878pt3 class b conducted safety ground leakage current 275 a @ 50/60 hz, 264 vac input output maximum power 100 w for convection (80 w for LPS102-M); 150 w with 30 cfm forced air (120 w for LPS102-M) adjustment range 10% minimum on the main outputs fan output 12 v @ 1 a isolated, 10% hold-up time 10 ms @ 150 w load, 120 vac input overload protection short circuit protection on all outputs. case overload protected @ 110-160% above rating overvoltage protection 15-35% above nominal output logical control power failure open collector logic signal goes high 100-500 msec after main output; it goes low at least 6 msec before loss of regulation remote sense compensates for 0.5 v lead drop min. will operate without remote sense connected. reverse connection protected. data sheet power
environmental specifcations operating temperature 0 to 50 c ambient derate each output as 2.5% per degree from 50 to 70 c. -20 c start up storage temperature -40 c to +85 c electromagnetic susceptibility designed to meet en61000-4; -2, -3, -4, -5, -6, -8, -11 level 3 humidity operating; non-condensing 10% to 95% rh vibration iec 60068-2-6 to the levels of iec721-3-2 mtbf calculated 534,000 hours at full load and 25 c ambient conditions, 230 v input, bellcore ordering information model number output voltage minimum load maximum load with convection cooling maximum load with 30cfm forced air peak load regulation 2 ripple p/p (pard) 3 LPS102-M 5 v 0 a 16 a 24 a 30 a 2% 50 mv lps103-m 12 v 0 a 8.3 a 12.5 a 14 a 2% 120 mv lps104-m 15 v 0 a 6.7 a 10 a 11 a 2% 150 mv lps105-m 24 v 0 a 4.2a 6.3 a 7a 2% 240 mv lps108-m 48 v 0 a 2.1a 3.1 a 3.5 a 2% 480 mv lps109-m 54 v 0 a 1.85 a 2.8 a 3.1 a 2% 540 mv 1. peak current lasting < 30 seconds with a maximum 10% duty cycle. 2. at 25 c including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings. 3. peak-to-peak with 20 mhz bandwidth and 10 f (tantalum capacitor) in parallel with a 0.1 f capacitor at rated line voltage and load ranges. 4. this product is a component power supply and is only for inclusion by professional installers within other equipment and must not be operated as a standalone product. emc compliance to appropriate standards must be verifed at the system level. this product is for sale to oems and system integrators, including through distribution channels. it is not intended for sale to end users. pin assignments connector lps100-m sk1 pin 1 neutral pin 3 line sk2 pin 1 common pin 2 common pin 3 common pin 4 common pin 5 +vout pin 6 +vout pin 7 +vout pin 8 +vout sk203 pin 1 common pin 2 power fail pin 3 - remote sense pin 4 + remote sense sk5 pin 1 +12 v fan pin 2 +12 v fan pin 3 fan return (isolated) pin 4 fan return (isolated) mating connectors ac input (sk1) molex p/n: 09-50-3031, pins: 08-52-0072 or landwin p/n: 3060s0302, pins: 3360t011p ac ground molex: 01-90020001 dc output (sk2) molex p/n: 09-50-3081, pins: 08-52-0072or landwin p/n: 3060s0802, pins: 3360t011p remote sense (sk203) molex p/n: 35155-0400, pins: 08-70-0056 or landwin p/n: 2640s04a0, pins: 2543t011p fan: (sk5) molex p/n: 22-01-1042, pins: 08-70-0049 or landwin: p/n: 2510s04a0, pins: 2543t011p artesyn embedded technologies connector kit #70-841-025, includes all of the above notes: 1. specifcations subject to change without notice. 2. all dimensions in inches (mm), tolerance is .02. 3. mounting holes m1, m2 should be grounded for emi purpose 4. mounting m1 is safety ground connection 5. specifcations are for convection rating at factory settings at 115 vac input 25 c unless otherwise stated. 6. this power supply requires mounting on metal standoffs 0.20 (5 m) in height. 7. for dc input an external dc safety rated fuse must be used. 8. warranty: 2 years 9. weight: 0.44 lb. / 0.20 kg lps100-m series data sheet
worldwide offices americas 2900 s.diablo way tempe, az 85282 usa +1 888 412 7832 europe (uk) waterfront business park merry hill, dudley west midlands, dy5 1lx united kingdom +44 (0) 1384 842 211 asia (hk) 14/f, lu plaza 2 wing yip street kwun tong, kowloon hong kong +852 2176 3333 for more information: www.artesyn.com/power for support: productsupport.ep@artesyn.com artesyn embedded technologies, artesyn and the artesyn embedded technologies logo are trademarks and service marks of artesyn embedded technologies, inc. all other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. ? 2016 artesyn embedded technologies, inc. all rights reserved. for full legal terms and conditions, please visit www.artesyn.com/legal . www.artesyn.com mechanical drawing sk1 sk2 sk20 3 2.00" (50.8) 4.00" (101.6) 1.72" (43.8) 1.29" (33.0) 3.72" (94.6) mounting hole ?0.16"[4.0] 4 places m ax. screw head diameter .22? (5.6) m1 m2 gnd vr1 output voltage adjust pot sk5 1 3 4 1 8 1 4 1 0.11? 0.197? (5.0) minimum standoff height (2.7) lps100-m ds 28sep2016 lps100-m series data sheet
|
